New to MSB.

Plastic grit media blasting.

 A less aggressive way to blast clean your parts including car bodies .
Costs. Hourly rate is charged @ £56.00 per hour plus materials used.
Emloying Plastic media is a higher coat than conventional blasting media due to the price of materials and extra time it takes to complete.
The finish will be smooth and bright. For further information please call our office.

Hard Plastic & Blast Media. with compounded glass filler for additional cutting ability.
For fast rust & paint removal. This product works we know we use it in our own blast room & cabinets. Bulk discounts available.

We can supply this product direct to your door for £19.95 per 25kg plus delivery costs & vat.

Can be used in standard blast cabinets & Soda pots.

Out performs Soda Blasting and glass bead. Faster cheaper and a lot more effective in removing paint, light rust and general grime.

Not caustic as soda, no skin, eye or breathing effects. Although a face mask and eye protection should be used.

No adverse effects when trapped between panel work, where soda being caustic may damage steel & Aloy work if left in place when damp.

No fear of component distortion, which can occur with conventional blasting products.

Soda costs around £30.00 for 25kg and can only be used once against plasblast for £19.95 and a recycle rate up to 12 times making far more economical over soda.

Non Polluting. We can supply this product direct to your door for £19.95 per 25kg plus delivery costs

Plastic Media, Plastic Blast Media or Plastic Stripping first introduced in the mid-1980’s by the United States military to provide an environmentally acceptable alternative to chemical strippers.
Soft enough to not cause damage on the substrates, but aggressive enough just to remove paint , rust and coatings, without peening or damaging the surface or substrate.
Unlike chemical strippers, plastic media was found to be biodegradable, non-toxic and non-polluting and the process was accepted as the ideal method of achieving delicate surface preparation for a wide variety of materials and components.

At low pressures it was also observed that you were able to re-use and recycle the plastic between 3 and 12 times, depending on the hardness of the plastic – PBM, soon acquired a reputation as the ideal abrasive for the environmentally conscious blaster.

Alternative to Soda Blasting and much faster too.
Plastic Stripping Media is designed to outperform Soda Blast, it cuts quicker, removes paint faster, leaves a smoother surface and can be reused multiple times. additionally, it is environmentally inert and is NOT caustic unlike soda..

Available in a range of grit size
PlasBlast 2G with compounded glass filler for additional cutting ability, ideal for fast rust & paint removal.

A common and very cost effective way of stripping paint and coatings from ferrous and non-ferrous components is to acid or caustic dipping. However, although recognized as an inexpensive way of conducting this process, stripping of items such as a car body can give rise to numerous negative effects. The use of these aggressive chemical strippers can, for example, leave residual chemicals entrapped in the frames, joints and structure of a car, vehicle body or panel.

Additionally the inside of the vehicle body and panel will have been paint dipped by the manufacturer and this will then be removed by the acid/caustic stripper and cannot be replaced, leaving the inside of the body shell/panel open to possible corrosion from within. As an alternative process, only strips visible areas on a selective basis. Ideally suited not only to paint removal from steel and aluminum bodies, it will also work perfectly on composite and glass fibre vehicles and panels, with no fear of component distortion, which can occur with conventional blasting.

Unlike chemical strippers, plastic media was found to be biodegradable, non-toxic and non-polluting and the process was accepted as the ideal method of achieving delicate surface preparation for a wide variety of materials and components At low pressures it was also observed that you were able to re-use and recycle the plastic between 3 and 12 times, depending on the hardness of the plastic – PBM, soon acquired a reputation as the ideal abrasive for the environmentally conscious blaster. Several incarnations later, plastic media has developed into an abrasive that is used worldwide, and has many different types, gauged by the hardness of the raw material.

Read More Information blast cleaning and costs


Our Opening Times:
Monday to Friday: 9.00am – 5.00pm
Saturday: 9.30am – 12.00pm
Closed Bank Holiday weekends

Tel:01621 841100
Fax: 01621 842233

Unit 2a
Benbridge Industrial Estate,
Heybridge, Maldon, Essex CM9 4ER


Facebook Posts

Zerrin gold over chrome powder coat. ... See MoreSee Less

View on Facebook

Vauxhall Chevette in for blasting work. ... See MoreSee Less

View on Facebook

Another E-type blast cleaned using Garrett & fine glass bead. Showing sighs of previous panel beating & a fair amount of pudding. ... See MoreSee Less

View on Facebook

Flip colour powder coat with heavy metallic/ green-purple ... See MoreSee Less

View on Facebook

Now that's what you call a proper BBQ stove. Applied heat retaining primer & high temp ceramic. Anyone fancy a burger😉 ... See MoreSee Less

View on Facebook